A wood cantilever of length ~2.5 m is driven into resonance using the hand as a simple driver. Video recordings of these oscillations are analyzed to determine experimental second harmonic (n = 2) damped resonance frequencies. These frequencies are compared to theoretical ones, obtained from measurements of elastic moduli, damping properties, and…

We report a simple means to build a model atomic force microscope (AFM) using 3D printing of thermoplastic materials that are commercially available. The model has many of the key parts of an actual AFM including a z-axis stage, an AFM head with a cantilever assembly, and a laser source that reflects off of the back of the cantilever. Using a…

We describe here a low-cost experiment for introductory physics students where they compare the physical properties of aluminum and steel by means of cantilever oscillations. This, in turn, allows the students to improve their physical intuition about these materials. Further, the students can apply their physics and mathematics knowledge and…

In this article we present a simple technique for determination of the Young modulus of the material of a metallic ruler using it as a cantilever. This method employs with a slide potentiometer and a digital multimeter. The linear region of potentiometer resistance which is calibrated in terms of length has been used to record the load vs.…

The article introduces a low-cost Arduino sensor into the Young's modulus determination laboratory for physics university students. A stainless steel ruler is used as a cantilever beam. Its free end attached a mass is slightly bent and released to make it oscillate as a simple harmonic motion. The Arduino sensor detects the moving mass's frequency…

A couple of experiments analyzing the vibration of bars in different configurations using as a vibration sensor an electric guitar pickup are presented. The device is a versatile and easy to operate sensor that can be used in experiments involving the analysis of vibrations in rods and bars of different composition and in different configurations.…

Research into technological problem solving has shown it to exist in a range of forms and draw upon different processes and knowledge types. This paper adds to this understanding by identifying procedural and epistemic differences in relation to task performance for pupils solving a well-defined technological problem. The study is theoretically…

The theoretical and experimental solutions for vibrations of a vertical-oriented, prismatic, thin cantilever beam are studied. The beam orientation is "downwards", i.e. the clamped end is above the free end, and it is subjected to a transverse movement at a selected frequency. Both the behaviour of the device driver and the beam's weak-damping…

A persistent problem in engineering-focused science instruction is the "design--science gap," whereby learners focus on building successful engineering products, instead of focusing on the relevant scientific principles. This research explores (a) whether integrating contrasting cases into engineering activities can impact how deeply…

The interaction analysis presented by Kim and Roth examines nine students, their teachers, the learning task and materials in a mixed second and third grade science classroom during the school day. In the research narrative readers are introduced to two resourceful and creative groups of students as they work on a task assigned by their…

With increasing technological changes and needs in society, technology and engineering education has received much attention in school science. Yet, technology traditionally has been subordinated to science or simply taken as the application of science. This position has resulted in a limited understanding of teaching technological and engineering…

Technology and engineering educators can use a simple hacksaw blade to help students learn about deflection, as that which occurs in a beam. Here the beam is fixed at one end and allowed to deflect in a manner that is easy to see and measure--the hacksaw blade represents a cantilever, an overhanging structure. This simple and very inexpensive…

This article reports for the first time the use of a plastic optical fibre (POF) cantilever beam to measure the density of a liquid. The sensor is based on the Archimedes buoyancy principle. The sensor consists of a POF bonded on the surface of a metal beam in the form of a cantilever configuration, and at the free end of the beam a displacer is…

This study was conducted to examine the results of using a low-cost hands-on setup in combination with accompanying activities to promote understanding of the contact mode of atomic force microscopy (AFM). This contact mode setup enabled learners to study how AFM works by hand scanning using probing cantilevers with different characteristics on…

In this activity, students use a model created from a coffee cup or cardstock cutout to explore the working principle of an atomic force microscope (AFM). Students manipulate a model of an AFM, using it to examine various objects to retrieve topographic data and then graph and interpret results. The students observe that movement of the AFM…