This paper proposes a new methodology, Power Block Geometry (PBG), for the presentation of power electronics topologies that process ac voltage. PBG's strategy uses formal methods based on a geometrical representation with particular rules and defines a universe with axioms and conjectures to establish a formation law. It allows power…

Wind energy conversion systems (WECS) nowadays offer an extremely wide range of topologies, including various different types of electrical generators and power converters. Wind energy is also an application of great interest to students and with a huge potential for engineering employment. Making WECS the main center of interest when teaching…

This paper presents the basic features of a software system developed to support the teaching of digital logic, as well as the experience of using it in the Digital Logic course taught at the School of Electrical Engineering, University of Belgrade, Serbia. The system has been used for several years, both by students for self-learning and…

Switched-mode power supplies (SMPS) are becoming an essential part of many electronic systems as the industry drives toward miniaturization and energy efficiency. However, practical SMPS design courses are seldom offered. In this paper, a generalized MATLAB/SIMULINK modeling technique is first presented. A proposed practical SMPS design course at…

This paper presents the introduction of problem-based learning (PBL) in a power electronics course at the University of Oviedo, Gijon, Spain, by means of two practical projects: the design and construction of a switching-mode power supply (SMPS) prototype and the static study of a dc-dc converter topology. The goal of this innovation was for…

This paper describes an educational research experience that took place in the Electrical & Electronics Engineering Master's program offered at the Escuela Universitaria de Ingenieria Tecnica de Telecomunicacion, Universidad Politecnica de Madrid, Madrid, Spain. The focus is to provide details of the motivation behind and the design and subsequent…

Technological literacy education involves the teaching of basic engineering principles and problem solving, including elementary electrical circuit analysis, to non-engineering students. Learning materials on circuit analysis typically rely on equations and schematic diagrams, which are often unfamiliar to non-engineering students. The goal of…

Project-based learning (PBL), a learning environment in which projects drive learning, has been successfully used in various courses in the educational programs of different disciplines. However, concerns have been raised as to the breadth of the content covered and, in particular, whether PBL can be applied to specialized subjects without…

This paper presents a series of activities and educational strategies related to the teaching of digital electronics in computer engineering. The main objective of these methodologies was to develop a final tutored coursework to be carried out by the students in small teams. This coursework was conceived as consisting of advanced problems or small…

This paper describes the goals, pedagogical system, and educational outcomes of a three-semester curriculum in microelectromechanical systems (MEMS). The sequence takes engineering students with no formal MEMS training and gives them the skills to participate in cutting-edge MEMS research and development. The evolution of the curriculum from…

This paper presents a low-cost hands-on experiment for a classical undergraduate controls course for non-electrical engineering majors. The setup consists of a small dc electrical motor attached to one of the ends of a light rod. The motor drives a 2-in propeller and allows the rod to swing. Angular position is measured by a potentiometer attached…

The design of the drive system for an automatic machine and its correct sizing is a very important competence for an electrical or mechatronic engineer. This requires knowledge that crosses the fields of electrical engineering, electronics and mechanics, as well as the skill to choose commercial components based upon their technical documentation.…

Experimentation is important for learning and research in the field of power electronics and drives. However, a great deal of equipment is required to study the various topologies, controllers, and functionalities. Thus, the cost of establishing good laboratories and research centers is high. To address this problem, the authors have developed a…

Servomotors are widely used in computerized numerically controlled (CNC) machines, hence motion control is a major topic covered in undergraduate/graduate engineering courses. Despite the fact that several syllabi include the motion dynamics topic in their courses, there are neither suitable tools available for designing and simulating multi-axis…

This paper describes a novel Electrical Machine and Power Electronic Training Tool (EM&PE[subscript TT]), a methodology for using it, and associated experimental educational activities. The training tool is implemented by recreating a whole power electronics system, divided into modular blocks. This process is similar to that applied when…